R&G Racing Race Series Engine Case Cover Kit for Select Honda Motorcycles
Description
The R&G Race Series engine case cover kit for Honda CBR1000RR /SP/SP2 | 2 piece is designed to provide the highest level of protection for the expensive OEM cases in the event of a fall or spill. Hearty 4mm Polypropylene yields exceptional impact absorption and abrasion resistance. These premium Race Series case covers beef up the armored performance with the addition of replaceable slider pucks at the impact f
... read more-
Brand: R&GQuestions? Call 1-855-255-5550 or contact our sales team
- Description
- Part Numbers
- Fitment
- Resources
- Add a review
Description
The R&G Race Series engine case cover kit for Honda CBR1000RR /SP/SP2 | 2 piece is designed to provide the highest level of protection for the expensive OEM cases in the event of a fall or spill. Hearty 4mm Polypropylene yields exceptional impact absorption and abrasion resistance. These premium Race Series case covers beef up the armored performance with the addition of replaceable slider pucks at the impact face for even greater prevention of wear through. After a fall or slide just the slider puck itself can be replaced to restore full protective capabilities in only a few minutes. The Race Series cover kit is strongly advised for track day warriors and street riders as well since this somewhat inexpensive investment can save some serious money versus replacement of the costly magnesium case covers.
Mounting is painless as the original bolt holes can be reused with the provided replacement hardware without the need to perform any modifications. The R&G covers fit directly over the originals without the need to replace any gaskets or even spill a drop of oil. Total installation time is less than 5 minutes. Install the R&G Race Series engine case cover kit and ride into the sunset with confidence knowing your CBR is securely protected!
Features:
- Complete protection for the vulnerable & expensive OEM engine case covers
- Outstanding reduction in risk for breaking or wearing through the engine case covers in a fall or slide
- Stout 4mm Polypropylene construction is naturally impact absorbing & abrasion resistant
- Top of the line Race Series enhances protection with the addition of a replaceable slider puck at the impact face
- The replaceable slider puck further increases slide resistance & protection against wear through
- Just the slider puck itself can be replaced after a small spill to restore maximum protection in only minutes
- Unlike case sliders this case cover provides superior protection from top to bottom of the original case cover
- Fits directly over the OEM magnesium case covers
- Installation is simple & easy with the use of factory mounting holes & extended replacement hardware
- Gasket replacement or loss of oil is not needed during installation
- Approved by the AMA & used by BSB (British Superbike) race teams & California Superbike School
What’s in the box:
- Right side R&G Race Series engine case cover RG.ECC0236R
- Left side R&G Race Series engine case cover RG.ECC0235R
- Mounting hardware
- Installation instructions
R&G Engine Case Cover Fitment Guide
Part Numbers
Our part number: | RG.KEC0101R |
GTIN13 / EAN: | 5054817108317 |
Fitment
Resources
You may also like…
R&G Racing Engine Case Cover Kit for Honda CBR1000RR /SP/SP2 ’17-’18 | 2 Piece
Special order
$210.99 USD Add to cart
-
R&G Racing Race Series Titanium Radiator Guard for Select Honda Motorcycles
Low stock
$200.99 USD Add to cart
-
R&G Racing Tail Tidy Fender Eliminator for Honda CBR1000RR / SP / SP2 ’17-’18
Low stock
$185.99 USD Add to cart
-
Related products
R&G Racing Left and Right Side Engine Case Cover Kit for Select BMW Models
Low stock
$197.99 USD Add to cart
-
SW-MOTECH Left and Right Side Aluminum Cylinder Guards for Select BMW
Not currently available to order
-
Closeout
R&G Racing Engine Case Cover for Yamaha FJR1300 ’13-’15 | Left Hand Side
Special order
$107.99 USD Add to cart
-
What others are saying
There are no contributions yet.